Passing Format

Standard format:
[TranspCode:string];[WakeupCounter:4];[TimeStamp:8];[Hits:2];[RSSI:2];[Battery:2];[Temperature:2];[LoopOnly:1];[LoopId:1];[Channel:1];[InternalActiveData:2];[InternalData:1]=[CheckSum]

FW2.6 format after setting <CONFSET;B3;1>

[TranspCode:string];[WakeupCounter:4];[TimeStamp:10];[Hits:2];[RSSI:2];[Battery:2];[Temperature:+2];[LoopOnly:1];[LoopId:1];[Channel:1];[InternalActiveData:2];[InternalData:1];[ExtendedPassingFlags:2];[BackupChannel:1];[ExtraCode:x]=[CheckSum]

[TranspCode]

The code of the transponder

[WakeupCounter]

Overall wakeup counter of the transponder (new transponders start at 10000)

[TimeStamp]

Time stamp of the detection in number of ticks

Standard Format: 32 Bit - 256th seconds

FW 2.6 Format: 40 Bit - 2048th seconds

[Hits]

Number of times the tag was detected

[RSSI]

RSSI value, see full description of RSSI here

[Battery]

Battery level in volts - (00 - ff) => (0 - 25.5), eg. 1f = 3.0V

[Temperature]

Temperature in degrees Celsius - (00 - ff) => (0 - 255), eg. 1a = 26°C

FW 2.6: Signed Value from -20°C...49°C (HEX: -14...+31)

[LoopOnly]

1 if this detection was generated in Store Mode

[LoopID]

Loop ID, (0 - f) => (1 - 8)

[Channel]

Channel ID (0 - f) => (1 - 8)

[InternalActiveData]

Data transmission details of an Active Transponder. One byte. Lowest three bits: no channel access counter (number of times, the passing could not be transmitted because the transponder could not access the channel). Next three bits: no ACK counter (number of times the passing was transmitted, but no acknowledgement was received. Seventh bit: 1, if this passing could not be transmitted at all in a previous attempt (="stored passing", old passing), 0 otherwise. Highest bit: 1, if the transponder woke up from deep sleep, 0 otherwise. Hint: You can check if a passing is a stored passing using
[InternalData] & 0x40 == 0x40 (the seventh bit is set).

8	7	6	5	4	3	2	1
DS	ST	No ACK			Channel busy

[InternalData]

This field is only used for internal purposes.

[ExtendedPassingFlags]

Reserved for future use

[BackupChannel]

Indicates if a passing was received on primary or secondary 2.4Ghz channel

[ExtraCode]

Extra Code as programmed into Transponder. This is optional and only reported if transponder Extra Code is set.

[CheckSum]

This is a simple 8bit-rollover check sum over all characters in this line up to and exluding the ";" before this checksum. Only applys if confset 0xB1 was set.

Example Call

Example (standard format)

← PASSINGGET;1\n
→ PASSINGGET;00\n
→ 00000001;01\n
→ IKNWZ06;a153;093a9eb4;fe;71;1d;15;0;1;7;00;0\n
→ \n

Example (2x passings, additional FW2.6 data fields after <CONFSET;B3;1> with one transponder reporting an Extra-Code)

← PASSINGGET;1\n
→ PASSINGGET;00\n
→ 00000001;02\n
→ IKNWZ06;a153;093a9eb470;fe;71;1d;+15;0;1;7;00;0;00;1\n
→ ZILAL95;9087;093ab54213;fe;71;1d;+1a;0;1;7;00;0;00;0;A-1000\n
→ \n

Example (8x passings, additional FW2.6 data fields after setting <CONFSET;B3;1> and checksum after setting <CONFSET;B1;1>)

← PASSINGGET;1\n
→ PASSINGGET;00=90\n
→ 00000001;08=24\n
→ IKNWZ06;a153;093a9eb470;fe;71;1d;+15;0;1;7;00;0;00;1=85\n
→ ZILAL95;9087;093ab54210;fe;71;1d;+1a;0;1;7;00;0;00;0=42\n
→ ZILAL95;908e;093ad85370;fe;71;1d;+1a;0;1;7;00;0;00;0=7D\n
→ ZILAL95;9093;093af16d30;fe;71;1d;+1a;0;1;7;00;0;00;0=75\n
→ ZILAL95;90a9;093b5fe320;fe;71;1d;+1a;0;1;7;00;0;00;0=A5\n
→ ZILAL95;90b6;093ba10a00;fe;71;1d;+1a;0;1;7;00;0;00;0=91\n
→ ZILAL95;9144;093e6a2150;fe;71;1d;+1a;0;1;7;00;0;00;0=41\n
→ ZILAL95;915c;093ee28f50;fe;71;1d;+1a;0;1;7;00;0;00;0=AC\n
→ =00\n

Impulse Marker

Markers generated on impulse input at the headphone jack of LoopBoxes and USBTimingBoxes always have a TransponderCode of 00000127 (FW 2.6 and up - previously _____127) no matter where they were created. You can use the LoopId and Channel to filter for a specific loop box. WakeupCounter counter is started at loopID * 1000 and incremented with every impulse.

→ 00000127;1f40;01521ab6;00;00;14;7b;0;7;0;00;0\n

Cookie	LastUser
Descrizione	Memorizza il numero cliente dall'ultimo accesso tramite questo browser. Utilizzato, ad esempio, per precompilare l'input utente nell'area di accesso.

Cookie	Cookieconsent
Descrizione	Utilizzato per verificare se il banner dei cookie ti è stato mostrato negli ultimi 35 giorni. Memorizza anche le tue selezioni specifiche del banner dei cookie.

Cookie	contactform_flag
Descrizione	Controlla se la casella rossa con l'indicazione del modulo di contatto è già stata presentata in questa sessione del browser.checks if the red box with the contactform hint has already been presented in this browser session

Cookie	PHPSESSID
Descrizione	Questa chiave è necessaria per identificare anonimamente la sessione utente attuale dal nostro sistema. Essenziale per il carrello, il processo d'ordine, l'account cliente, ecc.This key is necessary to anonoumously identify the current user session by our system. Essential for shopping cart, order process, customer account etc.

Cookie	Vimeo
Descrizione	Utilizziamo la piattaforma video Vimeo per ospitare video e incorporarli nel nostro sito. Cliccando sul video, Vimeo può impostare cookie nel browser.

Cookie	analytics_storage
Descrizione	Controlla se è possibile memorizzare i cookie di Google Analytics per analizzare il comportamento degli utenti sul sito web e comprendere come i visitatori interagiscono con i nostri contenuti. Acconsentendo, ci aiuti a migliorare l'esperienza dell'utente.

Cookie	ad_storage
Descrizione	Controlla se è possibile memorizzare i cookie pubblicitari, che vengono utilizzati per pubblicità personalizzate e retargeting.

Cookie	ad_personalization
Descrizione	Regola se la pubblicità viene personalizzata in base al comportamento e agli interessi dell'utente per mostrare annunci su misura.

Cookie	ad_user_data
Descrizione	Controlla se i dati personali dell'utente possono essere elaborati per scopi pubblicitari, come informazioni su età, sesso o interessi.

Example Call

Contattaci!