Configuration parameter IDs and values/range

Parameter [parameter-id]	Description	Possible Values D = Default on startup [value]
01	Push Pre-warn (non persistent) Push pre-warn messages prior to real passing	00=disabled (D) 01=enabled
02	Blink/beep on repeated passing (non persistent) Blink LED on reception of a repeated passing.	00=disabled 01=enabled (D)
03	Impulse input or beep output Use the headphone jack as impulse input to generate a fake passing.	00=impulse-in 01=beep-out (D)
04	Auto-shutdown on power loss (non persistent) Switch off the box on power loss. Can be used if timing is finished and you want the USB Timing Box to shut down with the computer.	00=disabled (D) 01=enabled
05	Operation Mode (USB Timing Box only) usb-kiosk: for testing transponders, showing total number of passings and last transponder ID on the display. CH# and Loop# are automatically set, avoiding any collisions with other r\|r Active Systems. usb-timing: Standard Timing Mode. CH# and Loop# are selected by computer. usb-store&copy: Transponder will create a stored passing. V2 transponders will send a passing copy to this USB Timing Box. usb-repeat-impulse: USB Timing Box is in repeat mode. Getting passings is not possible in this mode.	05=usb-kiosk 06=usb-timing (D) 07=usb-store&copy 08=usb-repeat-impulse
06	Channel ID CH# used for wireless communication. Please note that the channels on the display are shown with an offset of +1, from 1-8.	00 - 07 => (1 - 8)
07	Loop ID Loop# of the wire loop. Please note that the IDs on the display are shown with an offset of +1, from 1-8.	00 - 07 => (1 - 8)
08	Loop Power Sets the power of the loop, from 0:off to 100:full (hex 64) power.	00 - 64
09	Blink dead-time Leave set to 15 (hex 0F), don't change!	02 - FF (default 0F)
0a	Charging via USB If the timing computer itself is running on battery, it might not be good idea to charge the USB Timing Box.	00:disabled 01:enabled (D)
0b	Use DTR The DTR line is used for improved timing accuracy, see Timebase Control section.	00:disabled 01:enabled (D)
a0	Tray Scan Power Sets the power of the loop, from 0:off to 100:full (hex 64) power.	01 - 64 (default 0F)
a1	Tray Scan interval Time span for which a single row or column is powered.	01 - FF in ticks (1/256th) (default 50)
a2	Tray Scan ramp up delay Time to ramp up loop power, before first scan	01 - FF in ticks (1/256th) (default E0)
a3	Tray Scan row to column delay Rows are scanned with scan interval first, then there is a delay, then columns are scanned with scan interval.	01 - FF in ticks (1/256th) (default E0)
a4	Repeat Row and Column cycle for another N repetitions Cycle thru rows 1 + N times. Cycle thru column 1 + N times.	01 - 0A (default 00)
b1	Enable CheckSum for all ASCII Protocoll communication (see here) Only applys to FW 2.5.22868 and up.	0 - 1 (default 0)
b2	Push Passings enable. Only applys to FW 2.6 and up. Values of 1 and 255 lead to endless pushing of passings Values > 1 and <= 254 tell the box to push exactly this number of passings. You need to refresh this value again if you want to receive the next passings.	0 - 1 / 2..254 (default 0)
b3	Enable FW Version 2.6 data reporting format (Signed Temperature, New Beacons Info, Timestamps with 2048th and dayadj)	0 - 1 (default 0)
b4	Enable Status Push Message every second: #S;[TickCount:8];[MainLoopCycles:4];[LoopStatus:2];[MeasuredLoopPower:2];[ChannelNoise:2];[BattPercent:2]\n\n #S;015405f2;11f7;00;2c;01;3b\n\n	0 - 1 (default 0)

Parameters 06-08 are stored in a non-volatile memory on power down.

Cookie	LastUser
Popis	Ukladá číslo zákazníka z posledného prihlásenia cez tento prehliadač. Používa sa napr. na predvyplnenie používateľského vstupu v oblasti prihlásenia.

Cookie	Cookieconsent
Popis	Používa sa na overenie, či vám bolo zobrazené banner cookie za posledných 35 dní. Ukladá tiež vaše špecifické voľby v banneri cookie.

Cookie	contactform_flag
Popis	Overuje, či bolo červené pole s upozornením na kontaktný formulár už zobrazené v tejto relácii prehliadania.checks if the red box with the contactform hint has already been presented in this browser session

Cookie	PHPSESSID
Popis	Tento kľúč je nevyhnutný na anonymné identifikovanie aktuálnej používateľskej relácie. Nevyhnutné pre nákupný košík, proces objednávky, zákaznícky účet atď.This key is necessary to anonoumously identify the current user session by our system. Essential for shopping cart, order process, customer account etc.

Cookie	Vimeo
Popis	Používame video platformu Vimeo na hosťovanie a vloženie videí na našu webovú stránku. Po kliknutí na video môže Vimeo nastaviť cookies vo vašom prehliadači.

Cookie	analytics_storage
Popis	Overuje, či môžu byť uložené cookies Google Analytics na analýzu správania používateľov na webovej stránke a na pochopenie, ako návštevníci interagujú s naším obsahom. S vaším súhlasom nám pomáhate zlepšiť používateľskú skúsenosť.

Cookie	ad_storage
Popis	Overuje, či môžu byť uložené reklamné cookies, ktoré sa používajú na personalizovanú reklamu a retargeting.

Cookie	ad_personalization
Popis	Riadi, či sa reklama personalizuje na základe správania a záujmov používateľa, aby sa zobrazovali prispôsobené reklamy.

Cookie	ad_user_data
Popis	Riadí, či môžu byť osobné údaje používateľa spracované na reklamné účely, ako sú informácie o veku, pohlaví alebo záujmoch.

Kontaktuj nás!